Configuration
Received Packets
Update
Backup ▾
Create Backup
Restore Config
Device Reboot
LoRa APRS Configuration
Station Configuration
?
Callsign:
Symbol Overlay:
Symbol Table:
Beacon Comment:
Beacon Path:
Latitude:
Longitude:
WiFi Settings
?
Connect to WiFi Network
Connection Timeout (seconds):
Reconnect interval (minutes):
Access Point Settings
Auto AP Password:
Disable Auto AP after (minutes):
LoRa RF Settings
?
Transmitter (TX)
Enable TX
Frequency (MHz):
Speed:
BW 125khz CR 4:5 SF 12 (300bps)
BW 125khz CR 4:6 SF 12 (244bps)
BW 125khz CR 4:7 SF 12 (209bps)
BW 125khz CR 4:8 SF 12 (183bps)
BW 125khz CR 4:8 SF 10 (610bps)
BW 125khz CR 4:7 SF 9 (1200bps)
Power (dBm):
Receiver (RX)
Enable RX
Frequency (MHz):
Speed:
BW 125khz CR 4:5 SF 12 (300bps)
BW 125khz CR 4:6 SF 12 (244bps)
BW 125khz CR 4:7 SF 12 (209bps)
BW 125khz CR 4:8 SF 12 (183bps)
BW 125khz CR 4:8 SF 10 (610bps)
BW 125khz CR 4:7 SF 9 (1200bps)
Beacon Settings
?
Beacon Interval (min):
Send via RF
Send via APRS-IS
Send Beacon
Digipeater Settings
?
Disabled
Repeat only if own call is addressed
Act as WIDE1 (fill-in) digi
Act as WIDE2 digi
Voltage Monitoring
?
Send Internal Voltage
Send External Voltage
Send Voltage As Telemetry
External Voltage Pin:
Voltage Divider R1 (Ω):
Voltage Divider R2 (Ω):
Internal Voltage Calibration
Raw Input Min (V):
Raw Input Max (V):
Mapped Output Min (V):
Mapped Output Max (V):
External Voltage Calibration
Raw Input Min (V):
Raw Input Max (V):
Mapped Output Min (V):
Mapped Output Max (V):
Power Configuration
?
Cut-off Voltage (V):
Enable sleep on low voltage (for non-AXP devices)
TNC Settings
?
Enable TNC Server
Enable Serial KISS
Accept Own Frames
APRS-IS Settings
?
Enable APRS-IS connection
Server:
Passcode:
Generate
Connection Status:
Disconnected
Filter:
Allow messages from APRSIS to RF
WX Telemetry Settings
?
Activate Wx Telemetry
(Requires a BME/BMP280, BME680 or Si7021 sensor)
Height Correction (m):
Temperature Correction (°C):
Web Settings
?
Web Password:
Syslog Settings
?
Enable syslog
Mode:
log.lora-aprs.pl
lora-aprs.live
Syslog server:
Display Settings
?
Enable display
Display timeout:
(set 0 to disable)
Advanced Settings
?
CPU frequency:
40 MHz [use at your own risk!]
80 MHz
160 MHz
240 MHz
Reboot Interval (hrs):
Low Power Mode [dedicated for PV Digi]
Ignored callsigns (blacklist):
Don't send blacklisted packets via TNC
Admins callsigns (station operators):
Metrics
?
RX packets count:
-
TX packets count:
-
Repeated packets (Digi):
-
System Status
?
CPU Speed:
-
RAM usage:
-
Temperature:
-
Radio RSSI:
-
WiFi Strength:
-
Last Received Packets
?
Time
Packet
RSSI
SNR
Freq Error
Save Configuration